Crucial MX500 2TB 2.5" 7mm SATA III Internal SSD (with 7mm to 9.5mm spacer)
Seagate 2TB BarraCuda 5400 RPM 128MB Cache SATA 6.0Gb/s 2.5" 7mm Laptop Internal Hard Drive
Crucial MX500 1TB 2.5" 7mm SATA III Internal SSD (with 7mm to 9.5mm spacer)
OWC Envoy Pro External USB 3.0 Enclosure for June 2013-current model Apple Flash SSDs
Crucial 16GB (2x 8GB) CL11 DDR3L-1600 PC3L-12800 1.35V / 1.5V DR x8 204-pin SODIMM RAM Kit for Mac (or PC)
Crucial MX500 500GB 2.5" 7mm SATA III Internal SSD (with 7mm to 9.5mm spacer)
WD Blue 1TB 5400 RPM 128MB Cache SATA 6.0Gb/s 2.5" 7mm Laptop Internal Hard Drive
Crucial 8GB (2x 4GB) CL11 DDR3L-1600 PC3L-12800 1.35V / 1.5V DR x8 204-pin SODIMM RAM Kit for Mac (or PC)
Crucial 8GB (1x 8GB) CL11 DDR3L-1600 PC3L-12800 1.35V / 1.5V DR x8 204-pin SODIMM RAM Module for Mac (or PC)
Crucial MX500 250GB 2.5" 7mm SATA III Internal SSD (with 7mm to 9.5mm spacer)
Crucial 4GB (1x 4GB) CL11 DDR3L-1600 PC3L-12800 1.35V / 1.5V DR x8 204-pin SODIMM RAM Module for Mac (or PC)
- 2 Sockets
- 8 GB (Removable)
- Intel Core i5 2.9 GHz
- Flash - SDXC; SSD - SATA 2.5-inch 9.5mm
- ME087LL/A, A1418
- It is possible to upgrade to 16GB of RAM and hard drive in this system. Follow the guides below closely.
- iMac14,3 (Late 2013 21.5-inch) - EMC 2742
- INSTALLATION GUIDES
- - RAM Upgrade guide
- - HDD / SSD upgrade guide
- RAM Upgrade
- To upgrade the RAM in this iMac, you’ll need the general servicing kit to open it up, and your choice of RAM upgrade shown on the left. Follow this guide closely to install the RAM modules.
- HDD-> HDD or SSD
- The Late 2013 21.5-inch iMac models have a standard 1TB 2.5-inch factory HDD with a 6 Gb/s SATA port. At the time of purchase, Apple offered a 1 TB "Fusion Drive" (which combines a 128GB ‘blade’ SSD and a 1 TB hard drive), or a stand-alone 256GB/512GB blade SSD. To upgrade the factory 2.5-inch HDD, you’ll need the general servicing kit, plus a larger 2.5-inch HDD or 2.5-inch SSD. Follow this guide closely closely to upgrade.
- No additional thermal cable is needed for all 21.5-inch 2012-onward iMacs. If your fans are running fast after upgrading, you may not have reconnected one of the temperature sensors properly. Use the iStat widget to check which fan is running fast and check the associated sensor is connected properly.
- To clone your existing OS/app setup first, purchase a cloning cable or 2.5-inch HDD/SDD enclosure to connect your new HDD/SSD to your mac, then use the Super Duper app to perform the clone, then switch the drives. Your old 2.5-inch HDD can then be housed in the enclosure.
- If you have a ‘Fusion drive’ setup, then you’ll need to split the fusion drive first and then perform the clone operation.
- HDD + SSD or SSD->SSD
- There currently aren’t any supported aftermarket solutions to replace or upgrade the blade SSD in the Late 2013 and later iMac’s. However, if you currently have a HDD + SSD installed (Fusion drive), then you can upgrade the HDD to an SSD without having to remove the SSD part of the fusion drive. Just install OSX from scratch, and you can configure the two drives to work in parallel.
- The only upgrade path to upgrading an existing Vlad SSD is to install a genuine Apple SSD pulled from another machine. However, unlike the early 2013 model, even if your system was ordered with only a HDD installed, the PCIe connector for the blade SSD is still present on the motherboard.
- You can house your original factory Apple blade SSD in the Envoy Pro enclosure for June 2013 to current Macs.
- If you have only have a 'Blade' SSD installed
- All 'Tapered Edge' iMac's from the Late 2012 iMac13,1 up to the "Mid-2017" iMac18,3 models have a 6 Gb/s Serial ATA (Revision 3.0) connector that is occupied by a hard drive in the default configurations. However, if you customised your model and it only has a 'Blade' SSD installed, then you can still install a standard SATA 2.5" hard drive in 21.5-Inch models and a 3.5" hard drive in 27-Inch models. An SSD can also be installed in this hard drive space as well.