WD Black 4TB 7200RPM 128MB Cache SATA 6.0Gb/s 3.5" Desktop Internal Hard Drive
Crucial MX500 2TB 2.5" 7mm SATA III Internal SSD (with 7mm to 9.5mm spacer)
WD Blue 4TB 5400RPM 64MB Cache SATA 6.0Gb/s 3.5" Desktop Internal Hard Drive
Crucial MX500 1TB 2.5" 7mm SATA III Internal SSD (with 7mm to 9.5mm spacer)
WD Blue 3TB 5400RPM 64MB Cache SATA 6.0Gb/s 3.5" Desktop Internal Hard Drive
WD Black 1TB 7200RPM 64MB Cache SATA 6.0Gb/s 3.5" Desktop Internal Hard Drive
Samsung 8GB (1x 8GB) CL11 DDR3-1600 PC3-12800 1.5V ECC 240-pin EUDIMM RAM Module
Crucial MX500 500GB 2.5" 7mm SATA III Internal SSD (with 7mm to 9.5mm spacer)
- 32GB (Apple Official)
- 96GB (RamCity Approved and Fully Tested)
- * 64-bit mode is required to utilise more than 32GB
- 8 Sockets (4 sockets per processor)
- 6GB (Removable)
- Dual 2.26 GHz Intel Quad-core Xeon E5520 (Gainestown/Nehalem) processors
- SSD - SATA 3.5-inch, SATA 2.5-inch 9.5mm
- SSD - SATA 3.5-inch
- MB535LL/A; MB535T/A; MB535X/A
- Single module configurations will not work. At least two RAM modules must be installed. Up to 96GB can be installed using 2,4,8 and 16GB modules.
- MacPro4,1 8-core 2.26 GHz 2008 Model A1289 EMC 2314
- Latest Supported OS: OSX 10.11.x (El Capitan)
- EFI Architecture: 64-bit
- INSTALLATION GUIDES
- - RAM upgrade guide
- - HDD/SSD upgrade guide
- - PCI Express card upgrade guide (for installing a blade SSD or GPU)
- RAM Upgrade
- Up to 96GB of total RAM can be installed. Single module setups will not work and there must be at least two RAM modules installed in the machine. 16GB ECC registered modules cannot be mixed with 4GB or 8GB ECC unbuffered modules. No tools are required. Follow this guide to install the RAM modules.
- High Speed Blade SSD
- For a super-high speed bootable storage solution, you can't go past a M.2 PCIe (AHCI) SSD. It's compatible in any version of MacOS and in any of the square-shaped Mac Pro models from 2006 up to 2012, and also supports dual-SSD RAID 0 configurations for even higher speeds. See the extensive review on how well these SSD's perform on barefeats.com
- Look left for the supported models of the Samsung XP941 or SM951 which, when combined with the Lycom DT-120 or Angelbird WIPX1-FWKF PCIe adapter card, allow you to install and boot one (or more) of these SSD's in a spare PCIe slot.
- To install one of these cards, see the PCI Express card install guide for more information, and checkout the DT-120 product page for an extensive video on how to populate it with a blade SSD.
- The Mac Pro 2009 models have a 640GB 3.5-inch factory HDD with a 3 Gb/s SATA port, with 3 additional HDD storage bays. Due to the different screw hole patterns on larger capacity drives, only the 1/2/4TB WD Blue or WD Black models are compatible with the original drive sled design. However, for 2009 and later model Mac Pro's, you can purchase a replacement drive bracket which is compatible with the alternative screw hole design on larger capacity 6TB/8TB/10TB hard drives. To upgrade the existing HDD, purchase a larger 3.5-inch HDD and follow this guide to install it.
- HDD->SSD (replace or add in)
- To upgrade the factory 3.5-inch HDD to an SSD, purchase any 2.5-inch SSD. You will also need either the OWC Adaptadrive or Angelbird SSD Bay to properly adapt your new SSD to fit the Mac Pro drive sled. Follow this hdd install guide to install the SSD as the procedure is the same.
- To clone your existing OS/app setup from your old HDD to the new HDD / SSD, purchase a cloning cable or 2.5-inch HDD/SDD enclosure to connect your new SSD to your mac, (or just install it in a spare internal drive bay) then use the Super Duper app to perform the clone, then switch the drives or change the startup volume. If you don't plan to keep them installed internally, your old 3.5-inch HDD's can be housed in this 3.5-inch HDD enclosure.
- Graphics Card Upgrade
- The MacPro4,1 factory GPU is a Nvidia GeForce GT 120 with 512MB GDDR3 RAM.
- A tried and tested option for upgrading the GPU (if you can still find one) is the EVGA Geforce GTX 680 with 2GB (or 4GB) DDR5 VRAM which offers considerable performance improvements. Note, if the GPU is meant for PC (rather than a rare made-for-mac version), then it will work out-of-the-box on your Mac, but you won't be able to see boot screens (if you want to run bootcamp), single user or verbose mode. To access these features, you will need to flash the GPU with a custom Apple ROM from a windows machine. (Do this at your own risk, as it will void your warranty!)
- Instructions for flashing a GTX680 are here.